-
Adapts the VC80, VC80x back hole pattern to industry standard AMPS. Threaded for M4 screws. Recessed for flush mounting
-
Out of stockCFLD Shifting Plate for Oracle Micros POS Terminal
-
Out of stockScanner Bracket for Oracle Micros POS - MOQ - 25 Units
-
Out of stockPosition your device higher or lower on the mount. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface. Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
-
Out of stockStandard Left/Right Extension Plate. 100 x 50 x 5 mm (3.94 x 1.97 x 0.20 in). Avoid interference with the dashboard controls/displays when using wide devices. To extend your device to the left or right from the Vehicle Mount (especially the ProClip Angled Mount) to avoid interference with the dashboard controls/displays. Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
-
Out of stockThis Pedestal Mount Round Mounting Plate creates an extra sturdy and secure mounting platform that can be used in aircrafts, boats and a variety of vehicles e.g. personal vehicles, commercial vehicles, emergency vehicles, police vehicles, trucks, tractors, fork lifts and RVs. Additionally, the Pedestal Mount Extension Rod can be used with mounts in retail stores, kiosks, gyms, conference rooms, trade shows etc.
-
Out of stockThis 6 inch aluminum Mount has teeth within the interlocking joints providing a very strong connection. It can be used in a variety of vehicles or fixed locations to mount a wide variety of products such as tablets and mobile computers. - These come in 2, 4, 6, 8 and 10 heights with and AMPS base and top and can be purchased in complete sets or as individual pieces. - The design allows you to mix and match the parts to create your own unique design/solution.
-
Out of stockThe VESA ProClip adapter plate attaches to any existing 75mm and 100mm VESA mounting system to create a new flat mounting surface to allow the attachment of ProClip specific mounts and other mounts/devices.
-
This base will give the stability needed to use the mount as part of a free-standing solution. This also for a more portable mount setup which can be easily moved but is still strong and sturdy. - Round base is 200 mm in diameter (7.9 in) - Supports heavy devices
-
Out of stockExtension plate allows a MSR device holder to be added to the ET5X with rugged frame Pre-drilled AMPS hole pattern Made from durable ABS plastic
-
Out of stockThe VESA ProClip adapter plate attaches to any existing 75mm and 100mm VESA mounting system to create a new flat mounting surface to allow the attachment of ProClip specific mounts and other mounts/devices. Attach to 75mm and 100mm existing VESA systems. Made in Sweden from Durable Machined Aluminum. 4 - Pre-drilled 4mm threaded AMPS pattern holes to easily attach ProClip products
-
The VESA ProClip adapter plate attaches to any existing VESA 75mm or 100mm mounting system. Use to create a new recessed mounting surface to allow the attachment of ProClip specific holders. 4 pre-drilled AMPS pattern pilot holes to attach ProClip holders more securely. 5 mm Diameter Holes accommodate up to M5 screws
-
Out of stockThis Extension Plate has pre-drilled holes for the AMPS hole pattern. This allows additional holders to be added to existing mounts. It features up to 5 positions in either portrait or landscape orientation. Additional holes allow for cables to be run through the plate for a clean installation. Extension plate allows an additional device holder to be added. Multiple Locations for AMPS hole pattern mounts. Made from durable steel. 11.8 in (30 cm) x 2.36 in (6 cm) x .12 in (3 mm)
-
Out of stockWhen attaching a ProClip device holder or Mount to a vehicle dashboard or other surface which lacks sufficient structural integrity to provide a stable mounting platform, we recommend the use of of our Reinforcement Plates for added stability and durability. - Simply drill the properly located AMPS hole pattern in your mounting surface, position the plate on the back side of the mounting surface. - Includes: Four M4 screws (20mm thread length) and lock washers
-
Out of stockThis Vibration Damper effectively reduces the shock and vibration transferred to your mobile computing device mounted in particularly demanding environments such as on heavy machinery or forklifts. Simply install the damper (using the included hardeware) between your mobile device holder/cradle and the mounting bracket or Arm that is attached directly to the vehicle or machinery. The machine screws will engage securely with the M4 threaded steel core within the rubber grommets. - Reduce vibration in your mounted device - Supports standard AMPS hole pattern - High density rubber grommets - Maximum supported weight: 1.5 kg (3.31 lbs)
