Shop
Original price was: $59.99.$51.36Current price is: $51.36.
Hard-Wired Power Supply with Dual USB Ports No Power Cables Input 12/24V to 2 Pin Molex Port. USB-C: 3.6 - 12V, 1.5 - 3A (18 Watts Max) USB-A: 5V, 3A - 9V, 2A 12V, - 1.5A (18 Watts Max) Up to 36 Watts Combined
Original price was: $34.99.$29.96Current price is: $29.96.
6 Pin Molex Male to Male Cable (70cm / 2.5 Feet) For 12V Power Supplies Connects Holder to Power Supply
Original price was: $34.99.$29.96Current price is: $29.96.
Power Cable (70 cm/2.5 feet) with 6 Pin Male Molex Connectors for use between the sliding power block and Voltage Conversion Box
Original price was: $24.99.$21.40Current price is: $21.40.
Power Cable with 2 Pin Molex Connectors and bare ends for Voltage Conversion Box 118 Inches (3 Meters)
Original price was: $44.99.$38.53Current price is: $38.53.
12/24VDC POWER 5VDC 2A FUSE
Original price was: $49.99.$42.80Current price is: $42.80.
ProClip Charging Box With Molex Connectors Power Supply Only Does not include cables or fuse. Output 5.4V, 2.7A
Original price was: $92.99.$82.20Current price is: $82.20.
Adapts the VC80, VC80x back hole pattern to industry standard AMPS. Threaded for M4 screws. Recessed for flush mounting
Original price was: $109.99.$94.19Current price is: $94.19.
CFLD Shifting Plate for Oracle Micros POS Terminal
Original price was: $82.99.$73.36Current price is: $73.36.
Scanner Bracket for Oracle Micros POS - MOQ - 25 Units
Original price was: $64.99.$55.65Current price is: $55.65.
AMPS Mount Kit 4 - M6 x 12mm Fasteners, Split Lock Washers M4 Universal Fastener Pack Zebra VC80, VC80x, VC8300
Original price was: $9.99.$8.55Current price is: $8.55.
AMPS Dashboard Backer Plate
Original price was: $14.99.$12.84Current price is: $12.84.
Position your device higher or lower on the mount. The Vertical Extension Plate attaches to the ProClip Dashboard Mount or directly to a flat surface. Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
Original price was: $14.99.$12.84Current price is: $12.84.
Standard Left/Right Extension Plate. 100 x 50 x 5 mm (3.94 x 1.97 x 0.20 in). Avoid interference with the dashboard controls/displays when using wide devices. To extend your device to the left or right from the Vehicle Mount (especially the ProClip Angled Mount) to avoid interference with the dashboard controls/displays. Extension plates may not line up with the pre-drilled holes on your ProClip mount. The included self-tapping screws can be used to screw anywhere into the mount face.
Original price was: $44.99.$38.53Current price is: $38.53.
This Pedestal Mount Round Mounting Plate creates an extra sturdy and secure mounting platform that can be used in aircrafts, boats and a variety of vehicles e.g. personal vehicles, commercial vehicles, emergency vehicles, police vehicles, trucks, tractors, fork lifts and RVs. Additionally, the Pedestal Mount Extension Rod can be used with mounts in retail stores, kiosks, gyms, conference rooms, trade shows etc.
Original price was: $39.99.$34.24Current price is: $34.24.
The VESA ProClip adapter plate attaches to any existing 75mm and 100mm VESA mounting system to create a new flat mounting surface to allow the attachment of ProClip specific mounts and other mounts/devices.
Original price was: $34.99.$29.96Current price is: $29.96.
VESA ADAPTER PLATE WITH 4 HOLES FOR SELF-TAPPING SCREWS (AMPS PATTERN)
Original price was: $54.99.$47.09Current price is: $47.09.
This base will give the stability needed to use the mount as part of a free-standing solution. This also for a more portable mount setup which can be easily moved but is still strong and sturdy. - Round base is 200 mm in diameter (7.9 in) - Supports heavy devices
Original price was: $34.99.$29.96Current price is: $29.96.
Extension plate allows a MSR device holder to be added to the ET5X with rugged frame Pre-drilled AMPS hole pattern Made from durable ABS plastic
Original price was: $64.99.$55.65Current price is: $55.65.
The VESA ProClip adapter plate attaches to any existing VESA 75mm or 100mm mounting system. Use to create a new recessed mounting surface to allow the attachment of ProClip specific holders. 4 pre-drilled AMPS pattern pilot holes to attach ProClip holders more securely. 5 mm Diameter Holes accommodate up to M5 screws
Original price was: $54.99.$47.09Current price is: $47.09.
This Extension Plate has pre-drilled holes for the AMPS hole pattern. This allows additional holders to be added to existing mounts. It features up to 5 positions in either portrait or landscape orientation. Additional holes allow for cables to be run through the plate for a clean installation. Extension plate allows an additional device holder to be added. Multiple Locations for AMPS hole pattern mounts. Made from durable steel. 11.8 in (30 cm) x 2.36 in (6 cm) x .12 in (3 mm)
Original price was: $54.99.$47.09Current price is: $47.09.
Short Extension Plate
Original price was: $39.99.$34.24Current price is: $34.24.
VESA Adapter Plate with Tilt-Swivel
Original price was: $29.99.$25.68Current price is: $25.68.
When attaching a ProClip device holder or Mount to a vehicle dashboard or other surface which lacks sufficient structural integrity to provide a stable mounting platform, we recommend the use of of our Reinforcement Plates for added stability and durability. - Simply drill the properly located AMPS hole pattern in your mounting surface, position the plate on the back side of the mounting surface. - Includes: Four M4 screws (20mm thread length) and lock washers
Original price was: $74.99.$64.21Current price is: $64.21.
This Vibration Damper effectively reduces the shock and vibration transferred to your mobile computing device mounted in particularly demanding environments such as on heavy machinery or forklifts. Simply install the damper (using the included hardeware) between your mobile device holder/cradle and the mounting bracket or Arm that is attached directly to the vehicle or machinery. The machine screws will engage securely with the M4 threaded steel core within the rubber grommets. - Reduce vibration in your mounted device - Supports standard AMPS hole pattern - High density rubber grommets - Maximum supported weight: 1.5 kg (3.31 lbs)
Original price was: $264.99.$226.93Current price is: $226.93.
10" Clamp Mount Kit OtterBox uniVERSE Rail with USB Cable 10 Clamp Mount Apple iPhone 11/12 Pro in uniVERSE Case
Original price was: $249.99.$214.08Current price is: $214.08.
Apple iPad (7th Gen) Forklift Kit with OtterBox uniVERSE
Original price was: $254.99.$218.36Current price is: $218.36.
Apple iPad Pro 10.5 or iPad Air 3 Forklift Kit with OtterBox uniVERSE
Original price was: $79.99.$70.70Current price is: $70.70.
MultiStand for Apple iPad Mini with Retina display. This Holder is made to fit the tablet without a case. Easily snap your device in and out of the holder. Provides for safer driving when viewing, accessing and operating your device in the vehicle. Custom fit to your bare device. Includes Tilt-Swivel to angle holder 15 degrees any direction. Rotate between portrait and landscape view. Combine with a ProClip vehicle mount to make a full mounting solution
Original price was: $154.99.$132.73Current price is: $132.73.
ModTek USB-C 3.1 Dock for Apple Devices
Original price was: $244.99.$209.79Current price is: $209.79.
ModTek USB-C 3.1 Dock with Hub, 3 x USB-A (1 x USB 3.0, 2 x USB 2.0), 1x USB-C PD 100W Port, No Power Supply for Apple iPad
